Just How to Set up a Bathtub Yourself
Just How to Set up a Bathtub Yourself
Blog Article
We have come across the article about Tools You Need to Install a New Bathtub directly below on the internet and believe it made perfect sense to write about it with you over here.
Installing a tub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old tub with a new one is additionally a moderately challenging task. If the old tub is easily obtainable, the task can move immediately; if you need to open a wall surface to get rid of the old tub as well as place the brand-new bathtub, the job is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Make certain you have actually certified yourself for the task as well as fit trying it. As opposed to hiring a professional to take control of a halfway-completed task, it is far better to consider utilizing one prior to you start. Opportunities are you might need a professional plumber to make tube connections.
This short article will assist you mount a brand-new bath tub in your bathroom if you have already purchased a new bathtub as well as do not require to transform the setup of your previous water supply pipelines.
Your devices and material checklist should comprise the following:
Getting ready for the Installation
Firstly, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the faucet block, it is very important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps unit to prevent strain on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets utilizing 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its last placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installment, then the first thing you need to do is separate the supply of water. After doing so, activate the taps to drain pipes any water continuing to be in the system. The procedure of removing the existing faucets can be quite troublesome due to the limited access that is commonly the case.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. When the faucets have been eliminated, the holes in the bath/basin will have to be cleansed of any type of old securing compound.
Prior to moving on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Utilizing both wooden boards under its feet, put the bath tub in the needed setting. The wood boards are handy in evenly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be attained by examining the level and adjusting the feet on the tub up until the level reviews degree.
To mount taps, fit the bottom of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and check all joints and brand-new pipework for leakages and tighten them if required. Fill up the tub as well as additionally examine the overflow outlet and the normal outlet for leakages.
Lastly, deal with the bathroom paneling as described in the manufacturer's instruction manual. Tiling as well as securing around the bath tub needs to wait till the bathtub has been used at least once as this will settle it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washing machines are in location between the tap as well as the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with typical tap connectors. The previous kind must be connected to the tap ends initially, tightening up only by hand. The supply pipes can later be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is required to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, causing problems with wetness as well as feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing voids up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Remember to constantly load the tub with water prior to securing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also quickly readily available on the market. It is a good idea to fit the floor tiles using waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate more info about How to Install a Bathtub Yourself? Try leaving feedback down below. We will be pleased to listen to your views about this blog. We hope to see you back again in the future. If you please take the time to distribute this blog if you enjoyed it. I treasure reading our article about How to Install a Bathtub.
Article
Report this page